SMT vs Through-Hole Technology (THT): Key Differences and When to Use Each
TL;DR / Key Takeaways
– SMT mounts components onto the PCB surface without drilled holes; through-hole technology (THT) inserts leads through drilled holes and solders them from the opposite side.
– SMT shrinks electronic products by 40–60% in volume and 60–80% in weight, and cuts assembly cost by 30–50% versus through-hole.
– SMT components are about one-tenth the volume and weight of equivalent through-hole parts, with lower solder-joint defect rates and better high-frequency performance.
– Through-hole still wins for high-power, mechanically stressed, and connector applications where surface joints are not strong enough.
– Many boards use mixed technology: SMT for density and THT for strength, which AISMT supports with both SMT and THT equipment and spare parts.
Choose the wrong assembly method at the design stage and you are locked into it — a board that ends up too big, too expensive, or too weak at the connectors. SMT and through-hole (THT) each solve a different problem, and picking between them is the first decision in any PCB design. AISMT supports both, with SMT and THT equipment and spare parts. This guide compares the two so you can decide with data instead of guesswork.
What SMT and THT Mean
SMT mounts components directly onto the surface of the PCB. The component sits on top of the board, and a solder joint bonds its terminals to the surface pads. No holes are drilled.
THT inserts each component’s leads through drilled holes in the board, then solders them on the opposite side. The leads pass through the board, creating a mechanically stronger joint.
The Five Key Advantages of SMT
SMT replaced THT as the dominant method because it delivers measurable gains across every dimension that matters:
| Factor | SMT | Through-Hole (THT) |
|---|---|---|
| Component size/weight | About 1/10 of equivalent THT part | Full-size leaded part |
| Product volume reduction | 40–60% smaller | Baseline |
| Product weight reduction | 60–80% lighter | Baseline |
| Assembly cost | 30–50% lower | Higher (more manual steps) |
| Solder joint defect rate | Lower | Higher |
Beyond the table, SMT offers three further advantages. First, it is easier to automate — pick-and-place machines assemble boards at 60,000–100,000 CPH, far faster than manual or semi-automatic insertion. Second, it has better high-frequency performance because surface-mounted parts have shorter leads and less parasitic inductance, reducing electromagnetic and radio-frequency interference. Third, it supports higher component density, which is why high-pin-count ICs — from QFPs to BGAs — can only be built as surface-mount packages.
When Through-Hole Still Wins
THT is not obsolete. It remains the right choice in four situations:
- High power — power transistors, transformers, and large capacitors generate heat and carry current that surface joints handle poorly.
- Mechanical stress — connectors, switches, and jacks that are physically pushed, pulled, or plugged require the through-board strength of a THT joint.
- High reliability under vibration — automotive and industrial boards subject to constant vibration often use THT for critical components.
- Prototyping and rework — through-hole parts are easier to hand-solder and replace without specialized equipment.
Mixed-Technology Boards
Most real products use both. A mixed-technology board places the bulk of components with SMT for density and cost, then adds THT for connectors, power devices, and other mechanically stressed parts.
This two-stage flow has a specific order: SMT components are placed and reflowed first, then THT parts are inserted and wave- or hand-soldered. The through-hole process runs after reflow because wave soldering or manual soldering would disturb surface-mount joints if done first.
Choosing the Right Process
The decision reduces to a simple question: does the component need mechanical strength or high power, or does it need density and speed?
- Density, speed, and cost → SMT.
- Power, stress, and connectors → THT.
- Both on one board → mixed technology, SMT first, THT second.
For manufacturers running both processes, AISMT supplies SMT spare parts (feeders, nozzles, maintenance parts) alongside THT equipment and consumables, so a single line can handle both assembly methods.
FAQ
Q: What is the difference between SMT and THT?
SMT mounts components onto the PCB surface without drilled holes, while THT inserts leads through drilled holes and solders them from the opposite side. SMT enables higher density; THT provides stronger mechanical joints.
Q: How much does SMT reduce product size and cost?
SMT reduces product volume by 40–60%, weight by 60–80%, and assembly cost by 30–50% compared to through-hole assembly.
Q: Why are SMT components smaller than through-hole parts?
SMT components have no leads that pass through the board, so they are about one-tenth the volume and weight of equivalent through-hole parts. This enables the miniaturization of modern electronics.
Q: When should I use through-hole instead of SMT?
Use through-hole for high-power components, mechanically stressed connectors and switches, vibration-prone automotive or industrial boards, and prototyping where hand-soldering is required.
Q: What is a mixed-technology PCB?
A mixed-technology PCB combines SMT and THT. SMT components are placed and reflowed first, then THT parts are inserted and wave- or hand-soldered, so the through-hole process does not disturb the surface-mount joints.

Add comment